Jiangyin Yifa Metal Science & Technology Co., Ltd
www.steelwiredrawingmachine.com
Add to Cart
Automatic Ф 115mm - Ф 120mm 4500*840*1720mm Welded Wire machine for copper rope and spring industry
Function features-- Automatic Welded wire Mesh Machine
1. This kind of wire mesh welding machine is our latest developed reinforcing mesh welding machine.
2. The line wire and the weft wire of wire mesh welding machine are pre-straight and pre-cut.
3. The line wire is feeding by the servo motor ,pulling the wire net by the servo motor auto.
4. The wire mesh welding machine welding power comes from the cylinders. It’s easy to control the welding pressure .
5. The weft wire of wire mesh welding machine feeding from the multi hopper which capacity is more over ten times than the traditional hopper.
6. The new wire mesh welding machine added the bear wire net and carry equipment that makes the working more convenience .
7. The welding part of wire mesh welding machine is used the springiness input wire trunking that makes the welding copper use for long time.
8. This wire mesh welding machine adopts synchronous control technique. The cent-control and welding time are composed of PLC program system. The input front-panel is touch screen , the operate is more intelligent and reasonable.
Technology parameters
Features:
easy operation,low noise,high efficiency
The production process:
№1 Pretreatment, rough production line
Steel wire pretreatment(including:Pay-off stand + Disorderly parking+New type(water clean)+ Electrolytic pickling + boron coating + High frequency drying + LZ6/560 straight-line wire drawing machine + SG800 I-spool take-up machine or none stop take-up machine
№2 Fine drawing production line
FX800 I-spool(or rotary ) wire pay-off machine + LZ8/400(or LZ7/400)Straight line wire drawing machine + Tension stand + Wash tank + SG630I-spool wire take-up machine
№3 Chemical copper plating production line
№4 Layer and packing production line
SG630 spool pay-off machine (active type) + middle + layer winding machine
№5 S4525 heat shrinkable packaging machine for packaging, warehousing
Wire Drawing Machine
usage:
this model of wire drawing machine can draw the low carbon,medium carbon,high carbon wire and the material of wire can be copper,aluminum,etc.so it is suitable for woodenscrews,electric lead,copper rope ,spring industry.
production equipment parameter
1. Wire material surface pre-treatment
1.1 high shelf pay-off:Put a wire rod, without motor
1.2 Scribble and automatic stop switch: wire out
of the pay-off machine through the steel ring with
a diameter of 200 mm, if a few circle wire
entwined, steel ring that was taken to the other
side, t the bottom of the stroke switch will send
signals, and the entire line emergency stop.
1.3 Repeated bending mechanical shell and
wire ball strong scrubbing device: the wire rod
at least six direction perpendicular(National
initiative)Bending heat treatment to strip iron
oxide on the surface of the wire.
Eight peeling wheel, material: ZG45 steel, hardness of HRC50, Wheel
inner diameter Ф 115 --- Ф 120mm.
Wheel service life of 6000 hours. After
peeling ,the wire through period of tapered hole, use wire clean ball strongly wipe the
surface of wire rod, and does not damage
the wire surface, reduce the waste into the electrolytic pickling tank, ensure the
effect of pickling, facilitate drawing; By pressure cold water irrigation and block and
impurities, rust on the surface of the wire rod export high-pressure gas blowing
device, reduce by wire out of the water.
Take-up system:
№1 Ф800mm I-Spool take-up machine
① Main transmission adopts the transmission efficiency high service life long V transmitte take form;
②) With pneumatic brake and pneumatic top
device
③ Motor:15 kw variable frequency motor；
④ Ribbon cable with screw thread, maintenance
is simple and practical
⑤ take up by Ф800mm I-spool
⑥ There were equipped with a mechanical locking device, at any speed, power outages, fly out to ensure that the wheel will not hurt workers
